> >>Anycubic High Speed Resin LCD 405nm UV Sensitive Resin 1kg

3D Filament and Resin

Specials

Anycubic High Speed Resin LCD 405nm UV Sensitive Resin 1kg View larger

Anycubic High Speed Resin LCD 405nm UV Sensitive Resin 1kg

New product

Rs 9,200.00

Estimated Delivery: 1 to 3 days

Add to wishlist

More info

Product Features
● Print Up To 3X Faster
● Sturdy & Strong, Ensure Model Details
● Speedy & Stable, Clean At Ease

Resin Parameters

UV wavelength365-405nmElongation at break6-9%
Density1.15g/cm³Molding shrinkage5.1-6.2%
Viscosity55-65 cP·mPa·sFlexural strength60-85 MPa
Hardness90-93DFlexural modulus1800-3000 MPa
Tensile strength45-60 MPaConservation period12 Months

Recommended Printing Parameters

Printer ModelLayer ThicknessExposure TimeLight-Off TimeBottom Exposure TimeBottom LayerAnti-Aliasing LevelZ Lift DistanceZ Lift SpeedZ Retract Speed
Photon Mono M7 Pro0.1mm1.5s0.5s15s514mm15mm/s15mm/s
Photon Mono M5s Pro0.1mm1.9s0.5s10s513mm20mm/s20mm/s
Photon Mono M5s0.1mm1.7s0.5s10s313mm20mm/s20mm/s

Instructions for Use

(1) Before use:
Shake the liquid resin before use;
Clean the resin tank and the molding platform to keep the bottom of the resin tank in light
transmission.(2) When using:
Unscrew the cap and add it to the resin tank according to the equipment requirements;
Select the correct print parameters and settings for printing.(3) After use:
After printing, please use the matching tools for post-processing, including blade, diagonal
pliers,tweezers,containers,gloves;
ethanol(≥95%),lactate or isopropyl alcohol cleaning solution;(4) Post-processing steps:
A. Remove the printed model from the molding platform with a blade;
B. Submerge the model in the cleaning solution, rinsed or ultrasonically washed, then taken
out and drained; ANYCUBlC Wash and Cure machines are suggested to ensure better effect.
C.Proper processing, such as removing support, polishing, coloring, etc.

Precautions

  1. The ideal condition for storing uncured resin is a cool, dark place at room temperature and protect from light
    to avoid high temperature or sunlight.
  2. Suggested operating temperature is 18-35'c, and a low temperature may affect the printing effect, thus, the
    resin can be properly preheated before use (not more than 60°C).
  3. If the resin pigment settles, it can be used after stirring or shaking.
  4. In order to ensure the performance of the resin, please take out the model in time after cleaning to avoid the model soaking in water for a long time.
  5. To ensure the mechanical properties of the model, please perform post-curing in time after cleaning and drying.
  6. To ensure the ideal performance of the curable material, it is necessary to control the intensity and time of the
    light source after curing.Therefore, the following steps are recommended:
    (1) The intensity of mercury lamp or LeD light source is 5-10mW/m?, and the duration is no more than 1 hour (self-regulation);
    (2)The exposure time in the sun (summer) is around 1 hour;
    (3) Proximity or long-term exposure under strong light sources such as high-power high-pressure mercury
    lamps is prohibited.
    (4) lt is recommended to print in a dark room or be covered with a lid while printing as resin is a photosensitive
    material.

30 other products in the same category:

Customers who bought this product also bought: